Removing the factory tint from your car windows can be quite a task. Tint film is composed of two layers. When pulled, the top layer may come off without too much trouble but leave the second layer behind. The most effective system includes pulling both layers together. If done incorrectly, you may spend hours scraping off the stuck pieces of tint. With the proper steps, you can remove the factory tint yourself and save the money a professional would charge to do the job for you.

Instructions

Windshields

1

Remove any obstructions from the window, such as the rear brake light.

2

Spray the outside of the window with water and then cover it with plastic. Cut away excess plastic so that the tarp is roughly the shape of the window.

3

Lay a tarp across the rear deck and seats. Cover the front dashboard with plastic. Spray the inside of the window with pure ammonia. You may want to wear a face mask. Ammonia is very strong.

4

Cover the ammonia-soaked window with plastic and secure the plastic with tape.

5

Park the car in a sunny area. Leave the car for one hour.

6

Peel the tint off the window. Remove the plastic from the corner of the window. Leave as much the window covered as possible so the ammonia does not evaporate.

7

Spray the corner again with ammonia. Use a razor to pull away the corner of the tint. Be careful not to cut through any defroster lines or antennas. Once the corner rises, grab the loose piece with both hands and pull it away from the window. Pull slowly and with consistent pressure; the goal is to pull the film off in one piece. You will pull the plastic off as the tint pulls away from the window. If necessary, spray ammonia as you pull. If the tint film breaks, spray ammonia and use the razor to restart it.

8

Scrub off the adhesive residue stuck to the window once the film comes off. Spray the window glass again with ammonia. Use a fine steel wool pad to scrub off the adhesive.

9

Spray the window with window cleaner and wipe it down with paper towels or newspaper.

Side Windows

10

Spray the window down with warm, soapy water. Let soak for two or three minutes.

11

Use a razor blade in a holder and cut an opening in the tint.

12

Slide the blade under the tint at the opening you cut. Pull enough of the tint film away so you can grasp it with your hands.

13

Pull the film, using both hands, away from the window. Remove the film in segments until the window is clear.

14

Spray the window down again with warm, soapy water. Scrape away any adhesive residue. Clean the window with spray cleaner and paper towels.

Read More..

The rear drivers side windows on your vehicle may occasionally become stuck in either the closed or open position. The usual causes of this malfunction include the untimely failure of the window regulator or window motor. The window can also fall off or become stuck on its track if the glue holding the window to the track fails or if the track is obstructed by debris. Diagnosing and repairing this problem necessitates the removal of the interior door panel and trim.

Instructions

1

Turn the ignition key to the "On" position and attempt to operate the rear drivers side power windows. If you can hear the motor operating but the window wont move up or down, the window may be stuck on its track. If you cant hear the motor operating, the motor may need replacement. Check the fuses for the power windows before attempting to remove the window motor.

2

Disconnect the negative terminal cable from the battery with a wrench. This will decrease the likelihood of shock and prevent the battery from being drained.

3

Open the rear drivers side door. Remove the interior door panel and trim. The method for removing the panel and trim will vary depending on the vehicle. Consult your vehicles service manual and be sure to keep track of all clips and screws.

4

Inspect the windows track for signs of obstruction. You may need to apply a liberal amount of lithium grease to the track. If the window is off-track, clean the window of all adhesive and apply urethane-based glue to the windows mounting point. Reattach the window to the mounting point and leave the window undisturbed in the up position for one to two days.

5

Inspect the window regulator and motor. The window regulator will need to be replaced if the cables are snapped or frayed. If the window motor does not work, it will also need to be removed. Methods for removing both components may vary depending on the vehicle.

6

Reattach the door panel and trim to the rear drivers side door when finished. Close the door and reattach the negative terminal cable to the battery.

Read More..